(eredeti változat: http://danielnagy.wordpress.com/2009/10/25/ltspubuntu-3/ )
LTSP(Ubuntu):
Tartalom:
0. Buktatók
1. Friss, dedikált LTSP szerver készítése
2. Már meglévő szerverre létrehozni
0. Bukatók:
– én személy szerint a DHCP(v.3)-vel szívtam sokat, a többinél nem volt para
-2db hálókártya kell neki, mert különben nem akar majd elindulni a DHCP szolgáltatás
– Xinetd használhatatlanná tudja tenni a szolgáltatást
1. Friss install
– szedjük le az ubuntu legújabb válozatának “alternative” változatát, mondjuk innen:
http://releases.ubuntu.com/9.04/
- boot-oljunk be róla
– válasszunk nyelvet
– F4-et lenyomva válasszuk az “LTSP”-s opciót
– a főmenüből válasszuk ki a telepítést
– először az internetre csatlakozó hálókártyát kérdezi, megpróbálja dhcp-zni, aztán meg a dhcp-nknek választott másik kártyán is próbál dhcp-vel ip-t kérni:S de nem baj;)
– mindent next-next-next-finish-sel rakjunk fel, majd a telepítés végén létrehoz egy hálózati image-et. ezt fogják a kliensek leszippantani a hálózatról.
– a telepítés végén kivesszük/umount-oljuk a lemezt, reboot-olunk és ha minden jól megy működik a PXE és a dhcp is startup-ból fut
2. Már meglévő szerverre létrehozni
– két parancsot kell csak lefuttatni:
sudo apt-get install ltsp-server-standalone openssh-server; sudo ltsp-build-client
– az első telepíti az LTSP-t, a 2. meg létrehoz egy image-et
3. Forrásanyag:
Installing an LTSP Server
https://help.ubuntu.com/community/UbuntuLTSP/LTSPQuickInstall
Installing on top of an already running desktop system
You
need to set up one static network interface where you will attach the
thin clients, install two packages and run one command.
Configure
your spare interface for the thin clients to have the IP 192.168.0.1
(and make sure it is up and running). If you can’t get the new GNOME
network manager to work you can always install the older, simpler
version of network manager by going to the “add/remove” window and
searching “network”. Make sure to search “all available packages” and
“apply” the changes. You will find the new network manager under
settings -> network. Then follow the instructions below.
sudo apt-get install ltsp-server-standalone openssh-server
Now create your Thin Client environment on the server with.
sudo ltsp-build-client
*
*
/! If you are on a 64-bit system but your clients have another architecture use the –arch option eg. sudo ltsp-build-client –arch i386
After that, you will be able to boot your first thin client. If it doesn’t boot try rebooting the server.
/!
Note that if you want to use another IP than the above, you need to
edit the /etc/ltsp/dhcpd.conf file to match the IP values and restart
the dhcp server.
ThinClientHowto
https://help.ubuntu.com/community/ThinClientHowto
LTSP client environment
http://packages.ubuntu.com/jaunty/ltsp-client
LTSP on Ubuntu 8.04
http://beginlinux.com/server_training/linux-terminal-server/1053-ltsp-on-ubuntu-804
LTSP on Ubuntu Intrepid mini-HOWTO
http://edin.no-ip.com/content/ltsp-ubuntu-intrepid-mini-howto
UbuntuLTSP
https://help.ubuntu.com/community/UbuntuLTSP
Linux Terminal Server Project Administrator’s Reference
http://www.ltsp.org/~sbalneav/LTSPManual.html