Köszi!
Itt van a SMART összes adata nekem elég kínai de ti hátha le tudtok szürni belőle valamit.
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD502IJ
Serial Number: S13TJ1NQ700454
Firmware Version: 1AA01113
User Capacity: 500.107.862.016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3b
Local Time is: Tue Feb 2 19:48:43 2010 CET
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (7452) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 125) minutes.
Conveyance self-test routine
recommended polling time: ( 14) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 088 088 011 Pre-fail Always - 4610
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 840
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 5270
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 1
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 814
13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 11
184 Unknown_Attribute 0x0033 100 100 099 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 071 060 000 Old_age Always - 29 (Lifetime Min/Max 28/29)
194 Temperature_Celsius 0x0022 070 059 000 Old_age Always - 30 (Lifetime Min/Max 28/30)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 119939
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 19
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 8 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 87 10 d9 98 e4 Error: ICRC, ABRT at LBA = 0x0498d910 = 77125904
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 d8 bf d8 98 e4 08 04:48:38.210 WRITE DMA
ca 00 20 97 d8 98 e4 08 04:48:38.210 WRITE DMA
ca 00 08 07 43 91 e4 08 04:48:38.210 WRITE DMA
ca 00 08 ff ee 7d e4 08 04:48:38.200 WRITE DMA
ca 00 08 c7 ee 7d e4 08 04:48:38.200 WRITE DMA
Error 7 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 fe 46 92 e4 Error: ICRC, ABRT at LBA = 0x049246fe = 76695294
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 08 f7 46 92 e4 08 04:48:20.910 WRITE DMA
ca 00 08 df ff 7d e4 08 04:48:20.910 WRITE DMA
ca 00 08 b7 fe 7d e4 08 04:48:20.910 WRITE DMA
ca 00 08 5f da 7d e4 08 04:48:20.910 WRITE DMA
ca 00 08 0f d6 7d e4 08 04:48:20.910 WRITE DMA
Error 6 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 80 01 fe 46 92 a0 at LBA = 0x009246fe = 9586430
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 08 f7 46 92 e4 08 04:44:20.380 WRITE DMA
ca 00 08 bf 01 7e e4 08 04:44:20.380 WRITE DMA
ca 00 20 bf 01 7e e4 08 04:44:20.380 WRITE DMA
ca 00 08 bf 01 7e e4 08 04:44:20.380 WRITE DMA
ca 00 08 17 dc 7d e4 08 04:44:20.380 WRITE DMA
Error 5 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 80 01 01 00 00 a0 at LBA = 0x00000001 = 1
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 68 df db 9a e4 08 04:40:59.530 WRITE DMA
ca 00 b8 17 da 9a e4 08 04:40:59.530 WRITE DMA
ca 00 08 87 d5 9a e4 08 04:40:59.530 WRITE DMA
ca 00 08 8f ce 9a e4 08 04:40:59.530 WRITE DMA
ca 00 10 6f ce 9a e4 08 04:40:59.530 WRITE DMA
Error 4 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 83 bc 55 99 e4 Error: ICRC, ABRT at LBA = 0x049955bc = 77157820
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 00 3f 55 99 e4 08 04:22:35.900 WRITE DMA
ca 00 78 bf 54 99 e4 08 04:22:35.900 WRITE DMA
ca 00 c8 ef 53 99 e4 08 04:22:35.900 WRITE DMA
ca 00 90 57 53 99 e4 08 04:22:35.900 WRITE DMA
ca 00 58 f7 52 99 e4 08 04:22:35.900 WRITE DMA
SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision number = 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.