[törölve]
-a
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.0-kali3-amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital WD Blue 3.5 5400
Device Model: WDC WD10EZRZ-00Z5HB0
Serial Number: WD10EZRZ
LU WWN Device Id: 5 000c50 0a60866b5
Firmware Version: SDM1
User Capacity: 1,000,203,804,160 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database 7.3/5319
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri May 13 17:18:43 2022 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x71) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 167) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 082 064 006 Pre-fail Always - 144461069
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 071 071 020 Old_age Always - 30205
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 083 060 045 Pre-fail Always - 196553894
9 Power_On_Hours 0x0032 070 070 000 Old_age Always - 26710 (105 117 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1229
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 085 085 000 Old_age Always - 15
188 Command_Timeout 0x0032 100 094 000 Old_age Always - 30065295405
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 071 050 040 Old_age Always - 29 (Min/Max 21/29)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 12
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 192
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 211363
194 Temperature_Celsius 0x0022 029 050 000 Old_age Always - 29 (0 11 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 10227 (163 244 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 36356648175
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 40955750905
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 15 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 15 occurred at disk power-on lifetime: 13534 hours (563 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 00:00:47.662 READ DMA EXT
e1 00 0f 00 00 00 00 00 00:00:47.377 IDLE IMMEDIATE
ef 03 46 00 00 00 00 00 00:00:47.364 SET FEATURES [Set transfer mode]
ef 02 00 00 00 00 00 00 00:00:46.882 SET FEATURES [Enable write cache]
ef 90 06 00 00 00 00 00 00:00:46.869 SET FEATURES [Disable SATA feature]
Error 14 occurred at disk power-on lifetime: 13534 hours (563 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:00:41.468 READ FPDMA QUEUED
25 00 08 ff ff ff 4f 00 00:00:37.348 READ DMA EXT
e1 00 0f 00 00 00 00 00 00:00:37.063 IDLE IMMEDIATE
ef 03 46 00 00 00 00 00 00:00:37.050 SET FEATURES [Set transfer mode]
ef 02 00 00 00 00 00 00 00:00:36.338 SET FEATURES [Enable write cache]
Error 13 occurred at disk power-on lifetime: 13534 hours (563 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff 4f 00 00:00:37.348 READ DMA EXT
e1 00 0f 00 00 00 00 00 00:00:37.063 IDLE IMMEDIATE
ef 03 46 00 00 00 00 00 00:00:37.050 SET FEATURES [Set transfer mode]
ef 02 00 00 00 00 00 00 00:00:36.338 SET FEATURES [Enable write cache]
ef 90 06 00 00 00 00 00 00:00:36.324 SET FEATURES [Disable SATA feature]
Error 12 occurred at disk power-on lifetime: 13534 hours (563 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:00:30.252 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:30.252 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:30.251 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:30.251 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:30.251 READ FPDMA QUEUED
Error 11 occurred at disk power-on lifetime: 13534 hours (563 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff 4f 00 00:00:27.580 READ DMA EXT
e1 00 0f 00 00 00 00 00 00:00:27.578 IDLE IMMEDIATE
ef 03 46 00 00 00 00 00 00:00:27.566 SET FEATURES [Set transfer mode]
ef 02 00 00 00 00 00 00 00:00:27.548 SET FEATURES [Enable write cache]
ef 90 06 00 00 00 00 00 00:00:27.538 SET FEATURES [Disable SATA feature]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-H
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED